Yazar "Altunsoy, Mustafa" seçeneğine göre listele
Listeleniyor 1 - 12 / 12
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Antimicrobial and mechanical properties of dental resin composite containing bioactive glass(WICHTIG PUBLISHING, 2016) Korkut, Emre; Torlak, Emrah; Altunsoy, MustafaBackground: The aim of this study was to evaluate the antimicrobial efficacy and mechanical properties of dental resin composites containing different amounts of microparticulate bioactive glass (BAG). Methods: Experimental resin composites were prepared by mixing resin matrix (70% BisGMA and 30% TEG-DMA) and inorganic filler with various fractions of BAG to achieve final BAG concentrations of 5, 10 and 30 wt%. Antimicrobial efficacy was assessed in aqueous suspension against Escherichia coli, Staphylococcus aureus and Streptococcus mutans and in biofilm against S. mutans. The effect of incorporation of BAG on the mechanical properties of resin composite was evaluated by measuring the surface roughness, compressive strength and flexural strength. Results: Under the dynamic contact condition, viable counts of E. coli, S. aureus and S. mutans in suspensions were reduced up to 78%, 57% and 50%, respectively, after 90 minutes of exposure to disc-shaped composite specimens, depending on the BAG contents. In 2-day-old S. mutans biofilm, incorporation of BAG into composite at ratios of 10% and 30% resulted in 0.8 and 1.4 log reductions in the viable cell counts compared with the BAG-free composite, respectively. The surface roughness values of composite specimens did not show any significant difference (p>0.05) at any concentration of BAG. However, compressive and flexural strengths of composite were decreased significantly with addition of 30% BAG (p<0.05). Conclusions: The results demonstrated the successful utilization of BAG as a promising biomaterial in resin composites to provide antimicrobial function.Öğe Effect of different surface treatments on the microtensile bond strength of two self-adhesive flowable composites(SPRINGER LONDON LTD, 2015) Altunsoy, Mustafa; Botsali, Murat Selim; Sari, Tugrul; Onat, HalenurThe aim of this study was to evaluate the effect of different surface treatments on the microtensile bond strength (mu TBS) of two different self-adhesive flowable composite materials (SACs) to dentin. Forty extracted human molars were horizontally flattened to expose the dentin surfaces. The teeth were divided into eight groups according to the surface treatments (acid etching, Er:YAG laser quantum square pulse (QSP) mode, and Er:YAG laser medium-short pulse (MSP) mode at 10 Hz, 1.2 W, 120 mJ, and control-SiC) and SAC type (Vertise Flow and Fusio Liquid Dentin) (n = 5). Light cured 4-mm-high composite build-ups were made on the dentin surfaces, and the specimens were sectioned into serial sticks (n = 15). Later, the specimens were attached to microtensile testing machine and tensile force was applied at a crosshead speed of 1 mm/min until failure occurred. The failure modes were evaluated using a stereomicroscope at x40 magnification, and one sample from each group was used for scanning electron microscopy (SEM) evaluation. The data were analyzed with two-way ANOVA and Tukey's HSD test (alpha = 0.05). In all surface treatment groups along with the control groups, Vertise Flow showed better mu TBS than the Fusio Liquid Dentin with the exception of the Er:YAG MSP mode surface treatment (p < 0.05). Etching with phosphoric acid and the Er:YAG QSP mode surface treatment significantly increased the mu TBS of Vertise Flow (p < 0.05). Etching with phosphoric acid, Er:YAG QSP mode surface treatment, and Er:YAG MSP mode surface treatment significantly increased the mu TBS of Fusio Liquid Dentin (p < 0.05). The mu TBS of Vertise Flow was higher than the mu TBS of Fusio Liquid Dentin. The Er:YAG laser irradiation increased the mu TBS of both self-adhesive flowable resin composites in two pulse modes tested (MSP or QSP). However, the highest mu TBS was recorded when Vertise Flow was applied with acid etching.Öğe Effect of different surface treatments on the shear and microtensile bond strength of resin-modified glass ionomer cement to dentin(TAYLOR & FRANCIS LTD, 2014) Altunsoy, Mustafa; Botsali, Murat Selim; Korkut, Emre; Kucukyilmaz, Ebru; Sener, YagmurObjective. The aim of this study was to evaluate the effect of different surface treatments on the microtensile bond strength (mTBS) and shear bond strength (SBS) of resin-modified glass ionomer cement (RMGIC) to dentin. Materials and methods. Fifty-two extracted human molars were flattened to obtain dentin surfaces. For SBS assessment 40 teeth were divided into four groups according to their surface treatments (acid etching, Er: YAG laser QSP mode, Er: YAG laser MSP mode and control-SiC) (n = 10). A plastic cylinder was placed over the differently treated dentin surfaces and RMGIC was placed into the rings and polymerized. Twelve teeth were used for the mu TBS test. The treated dentin surfaces described above were restored with 4 mm high RMGIC and light cured; then, the specimens were sectioned into serial sticks (n = 15) and mu TBS and SBS were tested for failure in a testing machine with a 1 mm/min crosshead speed. The data were analyzed by one-way ANOVA and Tukey HSD tests (alpha = 0.05). Results. Acid etching showed significantly higher SBS than the other groups (p < 0.05). Er: YAG QSP and MSP-treated groups showed higher SBS values than the control group, but the difference was not statistically significant (p > 0.05). Er: YAG MSP showed the highest mu TBS value followed by acid etching, whereas the control group exhibited the lowest value (p < 0.05) and the differences between the control group and Er: YAG QSP were not significant (p > 0.05). Conclusions. The application of Er: YAG MSP mode and acid etching to dentin can be used for improving the bond strength of RMGIC.Öğe Effect of increased exposure times on amount of residual monomer released from single-step self-etch adhesives(SAGE PUBLICATIONS LTD, 2015) Altunsoy, Mustafa; Botsali, Murat Selim; Tosun, Gonca; Yasar, AhmetBackground: The aim of this study was to evaluate the effect of increased exposure times on the amount of residual Bis-GMA, TEGDMA, HEMA and UDMA released from single-step self-etch adhesive systems. Methods: Two adhesive systems were used. The adhesives were applied to bovine dentin surface according to the manufacturer's instructions and were polymerized using an LED curing unit for 10, 20 and 40 seconds (n = 5). After polymerization, the specimens were stored in 75% ethanol-water solution (6 mL). Residual monomers (Bis-GMA, TEGDMA, UDMA and HEMA) that were eluted from the adhesives (after 10 minutes, 1 hour, 1 day, 7 days and 30 days) were analyzed by high-performance liquid chromatography (HPLC). The data were analyzed using 1-way analysis of variance and Tukey HSD tests. Results: Among the time periods, the highest amount of released residual monomers from adhesives was observed in the 10th minute. There were statistically significant differences regarding released Bis-GMA, UDMA, HEMA and TEGDMA between the adhesive systems (p<0.05). There were no significant differences among the 10, 20 and 40 second polymerization times according to their effect on residual monomer release from adhesives (p>0.05). Conclusions: Increasing the polymerization time did not have an effect on residual monomer release from single-step self-etch adhesives.Öğe Evaluation of HEMA released from four different adhesive systems by HPLC(SAGE PUBLICATIONS LTD, 2015) Altunsoy, Mustafa; Botsali, Murat Selim; Ulker, Hayriye EsraPurpose: This study evaluated the elution of 2-hydroxyethyl methacrylate (HEMA) from 4 different adhesives, using high-performance liquid chromatography (HPLC). Materials and methods: The adhesives were applied on a bovine dentin surface and polymerized using an LED curing unit (n=5). After polymerization, specimens were stored in 75% ethanol solution (6 mL). Residual HEMA that was eluted from adhesives (after 10 minutes, 1 hour, 24 hours, 7 days and 30 days) was analyzed using HPLC. Statistical analyses were performed using 1-way ANOVA, Tukey HSD test and paired 2-sample t-test. Results: There were statistically significant differences among adhesive systems for the cumulative released HEMA and among the time periods (p<0.05). Clearfil SE Bond showed the highest amount of HEMA released, while Easy Bond showed the lowest. Among the time periods, the highest eluted HEMA value was detected in 10 minutes for all adhesives, and elution continued for up to 30 days. Conclusions: The HEMA eluted from adhesives was in different amounts, and the elution continued for a long time. The amount of eluted HEMA from adhesives used in this study was not viewed as critical for toxic reactions in biological tissues.Öğe Farklı cam iyonomer simanların kompozit ve kompomere olan makaslama bağlanma dayanım kuvvetlerinin karşılaştırılması(Selçuk Üniversitesi, 2015) Altunsoy, Mustafa; Ok, Evren; Küçükyılmaz, Ebru; Bölükbaş, Başak; Bilgin, Mehmet SelimBu çalışmanın amacı dört farklı cam iyonomer simanın kompozit ve kompomere olan makaslama bağlanma dayanımlarını karşılaştırmaktır. Gereç ve Yöntemler: Çalışma için 80 adet silindirik şekilli akrilik blok hazırlandı. Blokların düz yüzeylerinin ortasına 2 mm derinliğinde ve 3 mm çapında olan çukurcuklar açıldı. Bloklar dört gruba ayrılarak açılan çukurcuklar Ionoseal (Ionoseal, Cuxhaven, Almanya), Ketac Molar (3M EPSE, Seefeld, Almanya), Equia (GC Avrupa, Tokyo, Japonya) ve İmicryl (Imicryl SC, Imicryl Diş Malz San. Tic. AŞ, Konya, Türkiye) marka cam iyonomer materyalleri ile dolduruldu. Standart yüzeyler elde etmek için sertleşmeden önce cam iyonomerlerin üzeri şeffaf bant ile kapatıldı. Sertleşme tamamlandıktan sonra cam iyonomer siman yüzeylerine tek aşamalı adeziv (Futurabond M, VOCO GmbH, Cuxhaven, Almanya) uygulandı ve polimerize edildi. Her bir grup 2 alt gruba ayrıldı. Hazırlanan yüzeylerin üzerine yerleştirilen 2 mm yüksekliğinde ve 2 mm çapındaki aparatın içerisine taşmayacak şekilde doldurulan kompomer (Imicryl SC, Imicryl Diş Malz San. Tic. AŞ, Konya, Türkiye) ve kompozit (VOCO, Cuxhaven, Almanya) materyalleri üretici firmaların tavsiyeleri doğrultusunda LED ışık cihazı ile polimerize edildi. Universal test makinesi ile her bir örnekte kırılma meydana gelinceye kadar kuvvet uygulandı. Veriler iki yönlü varyans analizi ve Tukey çoklu karşılaştırma testleri ile istatistiksel olarak değerlendirildi (p=0.05). Bulgular: Ionoseal’ in kompozit ve kompomere olan makaslama bağlanma değeri diğer cam iyonomerlerden istatistiksel olarak daha yüksek bulundu (p < 0,05). Ketac Molar, Equia ve İmicryl’ in kompozit ve kompomere olan makaslama bağlanma değerleri arasında istatistiksel olarak fark gözlenmedi (p > 0,05). Sonuç: Rezin esaslı cam iyonomer siman olan Ionoseal kimyasal sertleşen Ketac Molar, Equia ve İmicryl cam iyonomer simanlara göre daha yüksek makaslama bağlanma değeri göstermektedir.Öğe Farklı polimerizasyon sürelerinin adeziv sistemlerden salınan artık monomer miktarına etkisi(2013) Altunsoy, Mustafa; Botsalı, Murat Selim; Tosun, Gonca; Yaşar, AhmetAMAÇ: Bu çalışmanın amacı, dört farklı polimerizasyon sü- resinde polimerize edilen üç farklı adeziv sistemin yapıla- rından salınan artık monomer miktarını tespit etmektir. GEREÇ VE YÖNTEM: Adeziv sistemler, üretici firmaların tali- matlarına uygun olarak kalınlığı 0.9 mm, bir kenar uzunluğu 7 mm olan dentin kesitleri üzerine uygulandı. Uygulama sonrası adeziv materyaller 10 sn., 20 sn., 40 sn. ve 60 sn. olmak üzere dört farklı sürede LED ışık cihazı kullanılarak polimerize edildi. Üzerlerine adeziv materyal uygulanarak polimerize edilen dentin kesitleri içlerinde %75lik etanol/su çözeltisi bulunan amber rengi cam şişelere alındı. Bu çö- zeltilerden 10. dk., 1. sa., 1. gün, 7. gün ve 30. gün olarak belirlenen zaman periyotlarında mikropipet kullanılarak ör- nekler alındı. Adezivlerden salınan artık monomer (Bis- GMA, UDMA) miktarları HPLC cihazı kullanılarak analiz edildi. Grupların genel ve ikili karşılaştırmalarında tek yönlü varyans analizi ve Tukey HSD testi kullanıldı. BULGULAR: Çalışmada incelenen materyallerden tüm zaman periyotlarında artık monomer salımının gerçekleştiği göz- lendi. Polimerizasyon süresinin arttırılmasıyla Clearfil S3 Bond (Bis-GMA) ve Clearfil Photo Bond (UDMA) adeziv ma- teryallerden salınan toplam monomer miktarlarının azaldı- ğı, polimerizasyon süresini arttırmanın diğer materyaller- den salınan toplam monomer miktarını etkilemediği göz- lendi. SONUÇ: Üretici firmalar tarafından tavsiye edilen polimeri- zasyon süresinin arttırılmasıyla bazı adezivlerden salınan monomer miktarı azalabilmektedir.Öğe Farklı sürelerde polimerize edilen adeziv sistemlerin yapılarından salınan artık monomer miktarının araştırılması(Selçuk Üniversitesi Sağlık Bilimleri Enstitüsü, 2012) Altunsoy, Mustafa; Botsalı, Murat SelimGünümüzde adeziv sistemler konservatif diş hekimliğinin tamamlayıcı bir unsuru olarak farklı uygulamalarla yaygın olarak kullanılmaktadır. Adeziv sistemler hidrofilik ve hidrofobik monomerler içermektedir. Bu monomerler tamamen polimerlere dönüşmemekte ve bir miktar monomer artık olarak kalmaktadır. Adezivlerden salınan monomerler ve adezivlerin içeriğindeki diğer komponentler ağız ortamına salınabilmekte ve canlı dokulara toksik etki gösterebilmektedir. Bu çalışmanın amacı; 4 farklı polimerizasyon süresinde (10 saniye, 20 saniye, 40 saniye ve 60 saniye) polimerize edilen adeziv sistemlerin yapılarından salınan reaksiyona girmemiş artık monomer miktarını 5 farklı zaman periyodunda (10. dakika, 1. saat, 1. gün, 7. gün ve 30. gün) belirlemek ve bu materyallerin sığır pulpa hücreleri üzerine sitotoksik etkilerini tespit etmektir. Sığır keser dişlerinden düşük hızla çalışan kesit cihazı (isomet) ile su soğutması altında bir kenar uzunluğu 7 mm ve kalınlığı 0,9 mm olan dentin kesitleri elde edildi. Adeziv sistemler, üretici firmaların talimatlarına uygun olarak dentin kesitleri üzerine uygulandı. Uygulama sonrası adeziv materyaller 10 sn, 20 sn, 40 sn ve 60 sn olmak üzere dört farklı sürede LED ışık cihazı kullanılarak polimerize edildi. Üzerlerine adeziv materyal uygulanarak polimerize edilen dentin kesitleri içlerinde % 75' lik etanol/su çözeltisi bulunan amber rengi cam şişelere alındı Şişeler ölçüm zamanına kadar 37 oC' lik etüvde bekletildi. Bu çözeltilerden 10. dakika, 1. saat, 1. gün, 7. gün ve 30. gün olarak belirlenen zaman periyotlarında mikropipet kullanılarak örnekler alındı. Adezivlerden salınan artık monomer (Bis-GMA, TEGDMA, UDMA) miktarları HPLC cihazı kullanılarak analiz edildi. Grupların genel ve ikili karşılaştırmalarında tek yönlü varyans analizi, Tukey HSD testi ve bağımlı t-testi kullanıldı. Adezivlerin sığır pulpa hücreleri üzerine sitototoksik etkilerinin incelenmesi aşamasında, adeziv sistemlerin ? primer ? ve ? bonding ? kısımları oda sıcaklığında saf etanolde (500 mg/ml) çözüldü. Daha sonra konsantrasyonları 10 mg/ml olacak şekilde kültür ortamında stok solüsyonu hazırlandı. İnkübasyon periyotlarından sonra hücre kültürlerinin kültür ortamı uzaklaştırılarak daha önceden seyreltilen polimerize edilmemiş adeziv sistemlerin her bir komponenti 200 µl materyal ekstraktı olacak şekilde kültür ortamına ilave edildi. Kontrol grubundaki hücrelere sadece serum içeren kültür ortamı ilave edildi. Hücre canlılığının belirlenmesinde MTT testi kullanıldı. Grupların karşılaştırılmasında tek yönlü varyans analizi ve Tukey HSD testi kullanıldı. Tüm materyallerden tüm zaman periyotlarında artık monomer salımının gerçekleştiği gözlendi ve en fazla salımın 30. g' de olduğu belirlendi. Çalışmada incelenen materyallerden kümülatif monomer salımı bakımından en fazla salımın Bis-GMA monomerine ait olduğu belirlendi. All Bond 3 adeziv materyalinden salınan monomer miktarlarının diğer materyallerden daha yüksek olduğu gözlendi. Polimerizasyon süresinin arttırılmasıyla sadece Clearfil Tri-S Bond (Bis-GMA), All Bond 3 (TEGDMA, UDMA) ve Clearfil Photo Bond (UDMA) adeziv materyallerden salınan toplam monomer miktarlarının azaldığı, polimerizasyon süresini arttırmanın diğer materyallerden salınan toplam monomer miktarını etkilemediği gözlendi. Sitotoksisite testinde, adeziv materyal komponentleri kontrol grubuyla karşılaştırıldığında tümünün sığır pulpa hücreleri üzerine sitotoksik etki gösterdiği belirlendi. Araştırmamızın sonuçlarına göre adeziv materyallerin tümünden farklı miktarlarda artık monomer salımı gerçekleştiği gözlendi. Üretici firmalar tarafından tavsiye edilen polimerizasyon süreleri büyük oranda yeterli bulundu. Bu çalışma ile polimerize edilmeyen adeziv materyallerin yüksek derecede sitotoksik etki gösterdikleri gözlendi. Bu yüzden derin kavitelerde veya pulpanın ekspoze olduğu durumlarda pulpa yüzeyinin kuafaj materyali ile örtülmesi tavsiye edilebilir. Ayrıca uygulama sırasında diş eti ve ağız içerisindeki yumuşak dokularla izolasyon sağlanarak adezivlerin bu dokulara olan toksik etkileri azaltılabilir.Öğe Fosfor plak kullanılarak farklı kaide materyallerinin radyoopasitelerinin karşılaştırılması(Selçuk Üniversitesi, 2015) Ağlarcı, Osman Sami; Garip, Gökçe; Ok, Evren; Altunsoy, MustafaRestorasyonlarda kullanılan dental materyallerin radyoopasitesi sekonder çürüklerin teşhisi, çürüğün restoratif materyalden ve diş dokusundan ayrılması, marjinal defektler, taşkınlıklar, açık marjinlerin tespiti ve pulpaya yakınlığın radyografik tanısında son derece önemli bir unsurdur. İdeal klinik performans için ihtiyaç duyulan radyoopasite derecesi materyalin türüne göre değişiklik göstermektedir. Radyoopasite ile ilgili çalışmalar genellikle mine, dentin ve alüminyum ile kıyaslanarak yapılmaktadır. Bu çalışmada cam iyonomer ve rezin esaslı farklı kaide materyallerinin radyoopasiteleri incelenerek; bunların mine, dentin ve alüminyum stepwedge’in radyoopasiteleri ile karşılaştırılması amaçlandı. Gereç ve Yöntemler: Sıklıkla kullanılan 5 kaide materyalinden (Nova Glass-F, Equia Fil, Ionofil, Vertise Flow, G-aenial Universal Flo) 10 mm çapında, 1 mm kalınlığında plastik disk şekilli örnekler hazırlandı. Yeni çekilmiş 3.molar dişlerden 1mm kalınlığında kesit alındı. Bütün örnekler fosfor plak üzerine yerleştirilerek fokal spot mesafesi 30 cm olacak şekilde 70 kVp ve 7 mAs’e görüntü alındı. Alınan görüntü Image J programına aktarılarak Mean Grey Value ölçüldü. Ölçülen değerin mmAl karşılığı hesaplanarak varyans analizi ve Tukey test ile analiz edildi. Bulgular: Vertise Flow, Nova Glass-F ve Equia Fil dentinden belirgin ölçüde yüksek radyoopasite değeri gösterirken (p < 0,05 ), İonofil ve G-aenial Universal Flo dentin ile benzer radyoopasite değeri göstermiştir (p > 0,05). Cam iyonomer içerikli kaide materyallerinin radyoopasite değerleri istatistiksel olarak benzer görülürken (p > 0,05), rezin esaslı kaide materyalleri birbirlerinden belirgin ölçüde farklı değerler göstermiştir (p < 0,05). Sonuç: Restoratif materyalin ve kaide materyalinin yeterli radyoopasiteye sahip olması önemli bir ihtiyaçtır. Buna karşılık piyasada yetersiz radoopasiteye sahip bazı kaide materyalleri de mevcuttur. Kaide materyallerinin radyoopasitesini değerlendiren çalışmalar periyodik olarak yapılmalıdır.Öğe Fracture Strength of Roots Instrumented with Self-Adjusting File and the ProTaper Rotary Systems(ELSEVIER SCIENCE INC, 2014) Capar, Ismail Davut; Altunsoy, Mustafa; Arslan, Hakan; Ertas, Huseyin; Aydinbelge, Hale AriIntroduction: The purpose of this study was to evaluate the fracture strength of roots instrumented with the Self Adjusting File (SAF; ReDent-Nova, Ra'anana, Israel) and the ProTaper system (Dentsply Maillefer, Ballaigues, Switzerland) and filled with the cold lateral compaction technique. Methods: In total, 50 mandibular premolar teeth were sectioned at or below the cementoenamel junction to obtain roots 13 mm in length. The roots were balanced with respect to buccolingual mesiodistal diameters and weight. They were distributed into 4 experimental groups and 1 control group (n = 10): no instrumentation (control group), instrumentation with ProTaper rotary files but no filling (PT), instrumentation with ProTaper rotary files and filling with cold lateral compaction (PT filling), instrumentation with SAF but no filling (SAF), and instrumentation with SAF and filling with cold lateral compaction (SAF filling). AH Plus sealer (Dentsply DeTrey, Konstanz, Germany) was used along with gutta-percha points. One week later, a vertical load was applied to the specimen's canal until fracture occurred. Data were statistically analyzed using 1-way analysis of variance (P =.05). Results: The mean fracture load was 244 +/- 51 N for the control group, 226 +/- 21 N for the PT, 242 +/- 45 N for PT filling, 233 +/- 14 N for the SAF, and 271 +/- 44 N for SAF filling. However, the differences were not statistically significant (P >.05). Conclusions: Instrumentation with the SAF or the ProTaper rotary system did not change the fracture strength of standardized roots with respect to cross-sectional diameter and weight.Öğe Orginal reseach article Effects of adhesive systems applied under fissure sealants to microleakage and shear bond strength(2015) Botsalı, Murat Selim; Küçükyılmaz, Ebru; Tosun, Gül; Altunsoy, Mustafa; Şener, YağmurThe aim of this study was to examine the effectof bonding agents under fissure sealants on bond strengthand microleakage.MATERIALS ANDMETHOD: A total of 210 freshly extracted noncarious human third molar teeth were used (105 teeth forshear bond strength and 105 teeth for microleakage assessment). The teeth were randomly assigned to 14groups, with 15 teeth in each group. Fissurit FX was applied to the etched enamel in the control groups. In the experimental groups, the self-etch adhesives: Clearfil SEBond, G Bond, Clearfil DC Bond and the total-etch adhesives: Prelude, Adper Single Bond and Optibond S wereapplied and light-cured followed by the subsequent application and light-curing of Fissurit FX. Shear bond strengthwas tested to failure in a universal testing machine with a1 mm/min crosshead speed. The shear bond strength datawas analyzed by using One Way ANOVA and Tukey HSDtests. Microleakage was evaluated by using a dye penetration method after mechanical loading and thermocycling. The microleakage data was analyzed by using theKruskal-Wallis and Tamhane tests.RESULTS: The microleakage of the Adper Single Bond Plusgroup was significantly less than that of the control group(p<0.05). However, the shear bond strength value of theAdper Single Bond Plus group was significantly less thanthat of the control group, again. The shear bond strengthvalue of Clearfil SE Bond was significantly greater thanthat of the control group (p<0.05).CONCLUSION: Clearfil SE Bond improved the shear bondstrength, and Adper Single Bond Plus decreased the miÖğe Residual monomer release from orthodontic adhesives cured with different light sources(TAYLOR & FRANCIS LTD, 2016) Botsali, Murat Selim; Sozer, Ozlem Akinci; Altunsoy, Mustafa; Demir, Abdullah; Ulker, Hayriye EsraIntroduction: The aim of this study was to evaluate the residual monomer release from orthodontic adhesives cured with light-emitting diode (LED) and halogen light sources.Methods: Seven hundred and twenty stainless steel brackets were divided into 3 groups according to the adhesive system used (Transbond XT light-cure adhesive [TXT], Transbond LR capsule [LR], and Light Bond light-cure adhesive paste [LB]), and each group was divided into 2 subgroups according to light-curing procedure (LED or halogen). Brackets were bonded with adhesives onto tooth buccal surfaces and polymerized. Each specimen contained 24 brackets that simulated the oral environment (n=5). The specimens were immersed in a 75% ethanol/water solution at 37 degrees C for 10min, 1h, 1 d, 7 d, 14 d, and 30 d, respectively. Eluted monomers (Bis-GMA, UDMA, and TEGDMA) were detected using HPLC.Results: There was residual monomer release at all time periods, and the highest amount of release was observed cumulatively on the 30th day. The cumulative Bis-GMA released from adhesives was not different (p>0.05). The cumulative TEGDMA released from adhesives was statistically different (p<0.05). There was no statistical difference between QTH and LED light-curing units for each adhesive (p>0.05).Conclusions: The release of residual monomers stays at a high level for a long time after polymerization. The total leaching of residual monomers from the Light Bond light-cure sealant resin plus Light Bond light-cure adhesive paste was higher than that of other materials for both curing units. Different curing units (LED or QTH) did not affect the monomer release from the orthodontic adhesives.