Yazar "Aslan, Muhammed Ali" seçeneğine göre listele
Listeleniyor 1 - 3 / 3
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Ana modelin elde edilmesinde vakumlu kabin tekniği(Selçuk Üniversitesi, 2015) Akpınar, Yusuf Ziya; Aslan, Muhammed Ali; Tatar, Numan; Yılmaz, BetülBu çalışmanın amacı farklı karıştırma ve döküm tekniklerinin alçının fiziksel özellikleri üzerine etkisini karşılaştırmaktır. Gereç ve Yöntemler: Çalışma planı iki yönlü olarak düzenlenmiştir; farklı karıştırma tekniklerinin alçının fiziksel özellikleri ve kalitesi üzerine etkisini incelemek. Örnekler karıştırma tekniklerine göre dört gruba ayrıldı: El ile karıştırma (Grup H), vakumlu mikser ile karıştırma (Grup VM), vakumlu kabin ile karıştırma (Grup VK), vakumlu mikser ve sonrasında vakumlu kabin kombinasyonu(Grup VM/VK) . Altmış örnek, üç nokta bükülme testi için hazırlandı. Model kırıklıkları kaydedilerek Kruskal-Wallis istatistik testi ile analiz edildi. Alt çene fantom akrilik dişler (Diş No: 43, 42, 41, 31, 32, 33) shoulder basamaklı metal desteksiz seramik veneer kron preparasyonu yapıldı ve ölçü alındı. Ana model üzerindeki poroziteler x40 büyütmeli mikroskop altında incelendi. Sonuçlar analizi için Tek Yönlü Varyans Analiz (? = 0.05) yöntemi kullanıldı. Bulgular: Sonuçlar göster, VM/VK tekniğinin modeldeki poroziteyi anlamlı ölçüde (p < 0.05) azalttığını ve modelin dayanım derecesini arttırdığını göstermiştir. En yüksek dayanım değeri Grup VM/VK' da (31.8 ± 0.7 MPa) oluşurken en az dayanım değeri Grup H' de (20.8 ± 0.1 MPa) oluştu. Sonuç: Vakumlu kabin ve vakumlu mikser tekniği ile kombinasyonu ana model dayanıklılığını arttırır ve poroziteyi azaltır. Bundan dolayı bu teknik ana modellerin dökülmesi için düzenli olarak kullanılabilir.Öğe Effect of different surface shapes formed by femtosecond laser on zirconia-resin cement shear bond strength(TAYLOR & FRANCIS LTD, 2015) Akpınar, Yusuf Ziya; Yavuz, Tevfik; Aslan, Muhammed Ali; Kepceoğlu, Abdullah; Kılıç, Hamdi ŞükürObjective: The purpose of this study was to evaluate the effect of different surface shapes formed by femtosecond (FS) laser on zirconia (Y-TZP)-resin cement shear bond strength (SBS). Background data: All ceramic restoration is used as an alternative to metal-ceramic restorations, due to its better aesthetics, strength, and toughness properties. However, bond strength of restoration to tooth and other materials is effective to long term success of the restoration, and to achieve it surface treatment is required on ceramic surface. Materials and methods: Forty square-shaped zirconia samples were prepared and assigned to four groups of 10. The details of the groups are as follows: Group A, square-shaped recessed surface; Group B, square-shaped projection surface; Group C, circular-shaped recessed surface; Group D, circular-shaped projection surface. The SBSs values were performed with a universal testing machine at a crosshead speed of 1mm/min. The data were analyzed statistically using analysis of variance (ANOVA) and Tukey HSD multiple comparisons tests. Results: The one-way ANOVA results on SBSs of the zirconia material bonded with resin cement revealed significant differences among the groups (p<0.05). The Tukey HSD test results revealed that Group B and D had significantly higher SBS values than other groups (p<0.05), but there were no significant differences between each other (p>0.05). Additionally, Group A and C had significantly lower values than other groups (p<0.05). Conclusions: Different surface shapes formed by FS laser provided a significant increase in SBSs. The SBS values of projection surfaces of circular and square-shapes are greater than that of recessed surfaces of circular and square-shapes.Öğe Effect of Femtosecond Laser Treatment on the Shear Bond Strength of a Metal Bracket to Prepared Porcelain Surface(MARY ANN LIEBERT, INC, 2015) Akpınar, Yusuf Ziya; Irgın, Celal; Yavuz, Tevfik; Aslan, Muhammed Ali; Kılıç, Hamdi Şükür; Üşümez, AslıhanObjective: The aim of this study was to investigate the effects of femtosecond laser treatment (Group FS) on the shear bond strength (SBS) of a metal bracket to prepared porcelain surface, and to compare it with other surface treatment techniques [50 mu m Al2O3 sandblasting (Group SB), 9.6% hydrofluoric acid gel (Group HF), and neodymium-doped yttrium aluminium garnet (Nd:YAG laser) (Group NY)]. Background data: Because of the increasing number of adult patients in current orthodontic practice, achieving sufficient bond strength of composite resin to porcelain restorations without bond failure during the treatment is a challenge for orthodontists. Methods: In total, 80 glazed feldspathic porcelain samples were prepared and randomly assigned to four groups of 20. Treated surfaces were treated with a silane agent. Brackets were bonded to porcelain samples. The specimens were stored in distilled water for 24 h and then thermocycled for 500 cycles between 5 degrees and 55 degrees C. The SBS of the brackets was tested with a universal testing machine at a crosshead speed of 1 mm/min, until bonding failure occurred. The data were analyzed statistically using analysis of variance (ANOVA) and Tamhane multiple comparisons tests. The results of ANOVA indicated that the SBS values varied according to the surface treatment method (p<0.001). Results: Results of the Tamhane post-hoc tests indicated that the bond strength in Group NY (5.11 +/- 1.53) was significantly lower than the other groups (p<0.05). There were no statistically significant differences among Groups SB (9.07 +/- 3.76), HF (9.09 +/- 3.51), and FS (11.58 +/- 4.16) (p=0.28). Conclusions: The results of this study showed that FS treatment produced high SBS of the processes assessed; therefore, it appears to be an effective method for bonding orthodontic metal brackets to prepared porcelain surfaces.