Effect of Preheating on Microhardness, Degree of Conversion, and Depth of Cure of Various Bulk-Fill Composites

Yükleniyor...
Küçük Resim

Tarih

2024

Dergi Başlığı

Dergi ISSN

Cilt Başlığı

Yayıncı

Selçuk Üniversitesi

Erişim Hakkı

info:eu-repo/semantics/openAccess

Özet

Background: This study aims to evaluate the effect of preheating onmicrohardness, degree of conversion, and depth of cure of bulk-fillcomposites (Tetric EvoCeram Bulk-Fill, SonicFill2) and a conventionalcomposite (Tetric EvoCeram).Methods: Layers of Tetric EvoCeram (2 mm), Tetric EvoCeram Bulk-Fill (4mm), and SonicFill2 (5 mm) were placed in 4-mm diameter molds andpolymerized at room temperature or heated to 55oC for 10 s with a totalnumber of 60 samples. Then, the top surfaces of the samples were polished.Thirty samples’ Vickers microhardness was measured from the top andbottom surfaces. The other 30 samples were pulverized into a fine powder,and the composites’ degree of conversion was measured with attenuatedtotal reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy.Obtained data were analyzed statistically with a significance level of p<0.05.Results: The degree of conversion of Tetric EvoCeram was higher than theminimum rate of clinically acceptable value, which is 55%, but the scores ofTetric EvoCeram Bulk-Fill and SonicFill2 were below the threshold.Preheating increased the degree of conversion of Tetric EvoCeram Bulk-Filland SonicFill2. In addition, preheating did not affect the depth of cure ofSonicFill2 but decreased the rate of Tetric EvoCeram Bulk-Fill.Conclusion: The results showed that the effect of preheating on the degreeof conversion and depth of cure varied according to the material.
Amaç: Bu çalışmanın amacı ön ısıtma işleminin bulk-fill kompozitlerin(Tetric EvoCeram Bulk-Fill, SonicFill2) mikrosertlik, monomer dönüşümderecesi ve polimerizasyon derinliği üzerine etkisini geleneksel birkompozitle (Tetric EvoCeram) karşılaştırmalı olarak incelemektir.Gereç ve Yöntemler: Kompozitler oda sıcaklığında veya 55oC’ye ısıtılarak4 mm çapında kalıplara Tetric EvoCeram 2 mm, Tetric EvoCeram Bulk-Fill4 mm ve SonicFill2 5 mm derinliğinde yerleştirilerek LED ışık kaynağıyla 10sn polimerize edilmişlerdir (n=5). Üst yüzeyleri cilalanan toplam 60 örneğinyarısının üst ve alt yüzeylerinden Vickers sertlik değerleri ölçülmüştür.Örneklerin diğer yarısı toz haline getirilmiş ve attenuated total reflectanceFourier transform infrared (ATR-FTIR) spectroskopisi ile monomer dönüşümdereceleri ölçülmüştür. Elde edilen veriler istatistiksel olarak analizedilmiştir (p<0.05).Bulgular: Tetric EvoCeram’ın monomer dönüşüm derecesi klinik olarakkabul edilen minumum değer olan %55’den yüksek olup, Tetric EvoCeramBulk-Fill ve SonicFill2 bu değerin altında kalmıştır. Ön ısıtma işlemi TetricEvoCeram Bulk-Fill ve SonicFill2’nin monomer dönüşüm derecesiniartırmıştır. SonicFill2’nin polimerizasyon derinliği ön ısıtmadanetkilenmezken, ön ısıtma Tetric EvoCeram Bulk-Fill’in polimerizasyonderinliğinde azalmaya neden olmuştur.Sonuç: Ön ısıtmanın monomer dönüşüm derecesi ve polimerizasyonderinliğine etkisi materyale bağlı olarak değişmektedir.

Açıklama

Anahtar Kelimeler

Preheating, bulk-fill composite, degree of conversion, depth of cure, microhardness, Ön ısıtma, bulk-fill kompozit, monomer dönüşüm derecesi, polimerizasyon derinliği, mikrosertlik

Kaynak

Selcuk Dental Journal

WoS Q Değeri

Scopus Q Değeri

Cilt

11

Sayı

1

Künye

Keleş, Z. H., Tarım, B., (2024) Effect of Preheating on Microhardness, Degree of Conversion, and Depth of Cure of Various Bulk-Fill Composites. Selcuk Dental Journal, 11(1), 27-32. Doi: 10.15311/selcukdentj.1219236