Experimental study and analysis of machinability characteristics of metal matrix composites during drilling

Basit Öğe Kaydı
dc.contributor.authorSalur, Emin.
dc.contributor.authorAslan, Abdullah.
dc.contributor.authorKuntoglu, Mustafa.
dc.contributor.authorGunes, Aydin.
dc.contributor.authorSahin, Omer Sinan.
dc.date.accessioned2020-03-26T20:14:12Z
dc.date.available2020-03-26T20:14:12Z
dc.date.issued2019
dc.departmentSelçuk Üniversitesi, Mühendislik Fakültesi, Metalurji ve Malzeme Mühendisliği Bölümüen_US
dc.description.abstractIn this study, the metal matrix composite materials were produced by hot press with various production parameters. The drilling experiments were performed on computer numerical control vertical machining centre without cutting fluid. Analysis of variance (ANOVA) was carried out in order to determine the effects of the production parameters on thrust force and surface roughness of metal matrix composites drilled with different feed rate. The effect of production parameters such as temperature, pressure and reinforcement ratio were investigated, and their effects were presented. The optimal level for each production parameters was determined by 'Maximize the S/N ratio approach with a Taguchi design'. The test results revealed that the reinforcement ratio was the main factor affecting the surface roughness of the metal matrix composites for both feed rate. However, same singularity was not matter on thrust force due to close contribution rates of production parameters and high error rates of analysis. In literature, an increase on the thrust force and the surface roughness values was reported as the feed rate increased during machining. Nevertheless, in our MMCs system, the thrust force and the surface roughness values were in tendency of declination / as the feed rate increased which makes this study more novel research.en_US
dc.description.sponsorshipScientific and Technological Research Council of Turkey (TUBITAK)Turkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [113M141]en_US
dc.description.sponsorshipThis work was supported by the Scientific and Technological Research Council of Turkey (TUBITAK) [grant number 113M141].en_US
dc.identifier.citationSalur, E., Aslan, A., Kuntoglu, M., Gunes, A., Sahin, O. S. (2019). Experimental Study and Analysis of Machinability Characteristics of Metal Matrix Composites During Drilling. Composites Part B: Engineering, 166, 401-413.
dc.identifier.doi10.1016/j.compositesb.2019.02.023en_US
dc.identifier.endpage413en_US
dc.identifier.issn1359-8368en_US
dc.identifier.issn1879-1069en_US
dc.identifier.scopusqualityQ1en_US
dc.identifier.startpage401en_US
dc.identifier.urihttps://dx.doi.org/10.1016/j.compositesb.2019.02.023
dc.identifier.urihttps://hdl.handle.net/20.500.12395/37839
dc.identifier.volume166en_US
dc.identifier.wosWOS:000467349000037en_US
dc.identifier.wosqualityQ1en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.institutionauthorSalur, Emin.
dc.institutionauthorAslan, Abdullah.
dc.institutionauthorKuntoglu, Mustafa.
dc.language.isoenen_US
dc.publisherELSEVIER SCI LTDen_US
dc.relation.ispartofCOMPOSITES PART B-ENGINEERINGen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.selcuk20240510_oaigen_US
dc.subjectMetal-matrix composites (MMCs)en_US
dc.subjectSurface propertiesen_US
dc.subjectMachiningen_US
dc.subjectDrillingen_US
dc.subjectANOVAen_US
dc.titleExperimental study and analysis of machinability characteristics of metal matrix composites during drillingen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
Emin SALUR.pdf
Boyut:
3.15 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Full Text Access
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Makine Mühendisliği/Makale Koleksiyonu
Metalurji ve Malzeme Mühendisliği Bölümü/Makale Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu