Bond strength of a silicone lining material to alumina-abraded and lased denture resin

Basit Öğe Kaydı
dc.contributor.authorUsumez, A
dc.contributor.authorInan, O
dc.contributor.authorAykent, F
dc.date.accessioned2020-03-26T16:47:56Z
dc.date.available2020-03-26T16:47:56Z
dc.date.issued2004
dc.departmentSelçuk Üniversitesien_US
dc.description.abstractThe aim of this study was to investigate the bond strength and adhesion of commercially available pollydimethylsiloxane denture liner (Molloplast-B) to alumina-abraded or lased heat-cured polymethyl methacrylate denture base resin. The effect of laser irradiation on denture base resin by a surface analyzer and scanning-electron microscopy (SEM) was also determined. Laser-treated specimens demonstrated statistically significantly higher surface roughness values compared to alumina-abraded and untreated (control-group) specimens (p < .05). There were no statistically significant differences in surface roughness between alumina-abraded and control specimens. In the tensile debonding test, no statistically significant differences were found among the treatment modalities tested (alumina abraded, lased, and control) (p > .05). Molloplast-B applied to alumina-abraded polymethyl methacrylate resin surface recorded the highest mean tensile bond strength. Laser-treated specimens produced the next highest mean tensile bond strength, and untreated polymethyl methacrylate resin surface recorded the lowest tensile bond strength. Laser irradiation produced significant surface texture changes of the denture base material. However, this mechanical surface preparation of denture base before application of a resilient liner did not improve the adhesion between denture base and soft lining material. (C) 2004 Wiley Periodicals, Inc.en_US
dc.identifier.doi10.1002/jbm.b.30078en_US
dc.identifier.endpage200en_US
dc.identifier.issn1552-4973en_US
dc.identifier.issn1552-4981en_US
dc.identifier.issue1en_US
dc.identifier.pmid15368245en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.startpage196en_US
dc.identifier.urihttps://dx.doi.org/10.1002/jbm.b.30078
dc.identifier.urihttps://hdl.handle.net/20.500.12395/18960
dc.identifier.volume71Ben_US
dc.identifier.wosWOS:000224190500025en_US
dc.identifier.wosqualityQ3en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.indekslendigikaynakPubMeden_US
dc.language.isoenen_US
dc.publisherWILEYen_US
dc.relation.ispartofJOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALSen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.selcuk20240510_oaigen_US
dc.subjectsoft denture linersen_US
dc.subjectpolymethylmethaerylateen_US
dc.subjectlaseren_US
dc.subjecttensile bond strengthen_US
dc.titleBond strength of a silicone lining material to alumina-abraded and lased denture resinen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
usumez2004 (1).pdf
Boyut:
214.14 KB
Biçim:
Adobe Portable Document Format
Açıklama:
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
PubMed İndeksli Yayın Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu